Joystick sensitivity and dead zone percentage (Custom FBW version)

[Manochvarma]

I am using custom FBW version. Seems the aircraft giving wobble effect (something like moving up and down vigorously). I need help on determining the sensitivity and deadzone so that I can fly it normally.

Sensitivity:
Initial state:

2nd try:

I am unable to reduce the wobble effect. Need some guidance.

[nyhmbo]

there is no support for the custom FBW version. but maybe a kind dev will help you anyways. no promise tho

[derl30n]

there any special steps? I downloaded unstable version from here. There is no any steps given.

Yes mb then, I was unaware of that.

[Manochvarma]

I cant see any readme files on the zip file I downloaded.

[Benjozork]

cc. @aguther

[Mike777-200ER]

How can the default FBW be disabled?

[Manochvarma]

How can the default FBW be disabled?

Default here means the A32NX which I downloaded were the version with custom FBW. So, in that file, there have set it as default.
I downloaded the file from here

You may check this:
#2316 (reply in thread)

[derl30n]

This is my setup.

[NathanInnes]

Did this help at all? @Manochvarma

[Manochvarma]

Did this help at all? @Manochvarma

No.

[Nadelbaum]

Not sure if it part of the instructions or whether it is anymore needed, but at some point you had to modify flight_model.cfg to support the custom FBW by changing the following:
fly_by_wire = 0
stall_protection = 0

Again, take this with a pinch of salt as I haven't tested the custom FBW since a week or so.

[Manochvarma]

Not sure if it part of the instructions or whether it is anymore needed, but at some point you had to modify flight_model.cfg to support the custom FBW by changing the following:
fly_by_wire = 0
stall_protection = 0

Again, take this with a pinch of salt as I haven't tested the custom FBW since a week or so.

I think its already in that number by default:

[airfirefighter]

Not sure if it part of the instructions or whether it is anymore needed, but at some point you had to modify flight_model.cfg to support the custom FBW by changing the following:
fly_by_wire = 0
stall_protection = 0
Again, take this with a pinch of salt as I haven't tested the custom FBW since a week or so.

I think its already in that number by default:

were?in the comunity/ a32nx /simobject/ airplanes /asobo or official??

[Mike777-200ER]

Looking in the FBW version I downloaded on 12/7, fly_by_wire and stall_protection are set to = 1.  I doubt the FBW/a32NX folks would put it out set incorrectly. I assume that files in the Community version always take precedence over the Official, ASOBO unmodified version. Mike firefighter[A32NX lover] wrote:

…

Not sure if it part of the instructions or whether it is anymore needed, but at some point you had to modify flight_model.cfg to support the custom FBW by changing the following: fly_by_wire = 0 stall_protection = 0 Again, take this with a pinch of salt as I haven't tested the custom FBW since a week or so. I think its already in that number by default: image <https://user-images.githubusercontent.com/75463793/101741424-fddd9f80-3b04-11eb-82eb-885bc0ecba7b.png> image <https://user-images.githubusercontent.com/75463793/101741509-1b126e00-3b05-11eb-9f00-d2caa76ff19d.png> were?in the comunity/ a32nx /simobject/ airplanes /asobo or official?? — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#2316 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AR7HZGAMNPTFHVH7JX5OK23SUMIUXANCNFSM4UTXRY3Q>.

-- Still sharp! 😐👩🏻‍⚕️👨🏼‍⚕️🎥📺

[Mike777-200ER]

CORRECTION: I just downloaded the latest available version of A32NX-master-cfbw  (downloaded 12-12-20) and both fly-by-wire and stall_protection are set to 0. firefighter[A32NX lover] wrote:

…

Not sure if it part of the instructions or whether it is anymore needed, but at some point you had to modify flight_model.cfg to support the custom FBW by changing the following: fly_by_wire = 0 stall_protection = 0 Again, take this with a pinch of salt as I haven't tested the custom FBW since a week or so. I think its already in that number by default: image <https://user-images.githubusercontent.com/75463793/101741424-fddd9f80-3b04-11eb-82eb-885bc0ecba7b.png> image <https://user-images.githubusercontent.com/75463793/101741509-1b126e00-3b05-11eb-9f00-d2caa76ff19d.png> were?in the comunity/ a32nx /simobject/ airplanes /asobo or official?? — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#2316 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AR7HZGAMNPTFHVH7JX5OK23SUMIUXANCNFSM4UTXRY3Q>.

-- Still sharp! 😐👩🏻‍⚕️👨🏼‍⚕️🎥📺